Gauge (bore diameter)

Gauge (bore diameter)

The Gauge or bore of a shotgun or rifle is a unit of measurement used to express the diameter of the barrel. The gauge or bore of a barrel is equal to the number of solid spheres of lead each having the same diameter as the inside of the barrel that would in total weigh a pound.

The term is also related to the measurement of black powder cannon, which were also measured by the weight of their round iron shot; a 6 pounder, for example, would fire a 6 pound (2.7 kg) spherical cast iron ball, which gave a bore diameter of about 91 mm (3.6 inches).

Historically, large double rifles were made in sizes up to 4-bore during their heyday in the 1880s, being originally loaded with black powder cartridges. These very large rifles, sometimes called elephant guns, were intended for use in India and Africa for hunting dangerous game.

Calculating gauge

An "n"-gauge diameter means that "n" balls of lead (density 11.352 g/cm³) with that diameter weigh one pound (453.5924 g). Therefore an "n"-gauge shotgun or "n"-bore rifle has a bore diameter (millimeters) of approximately

: d_n = left(frac{6 imes 453.59237~mathrm{g{11.352~mathrm{g/cm}^3 imes n imes pi} ight)^{1/3} = 42.416~mathrm{mm} imes frac{1}{sqrt [3] {n

Gauges in use

Since shotguns were not originally intended to fire solid projectiles, but rather a compressible mass of shot, the actual diameter of the bore varies quite a bit. The fact that most shotgun bores are not cylindrical also causes deviations from the ideal bore diameter.

The chamber of the gun is larger, to accommodate the thickness of the shotshell walls, and a "forcing cone" in front of the chamber reduces the diameter down to the bore diameter. The forcing cone can be as short as a fraction of an inch, or as long as 4 inches on some guns. At the muzzle end of the barrel, the choke can constrict the bore even further, so measuring the bore diameter of a shotgun is not a simple process, as it must be done away from either end.

Shotgun bores are commonly "overbored" or "backbored", meaning that most of the bore (from the forcing cone to the choke) is slightly larger than the value given by the formula. This is claimed to reduce felt recoil and improve patterning. The recoil reduction is due to the larger bore producing a slower acceleration of the shot, and the patterning improvements are due to the larger muzzle diameter for the same choke constriction, which results in less shot deformation. A 12 gauge shotgun, nominally 18.5 mm (0.729 inches), can range from a tight 18.3 mm to an extreme overbore of 20.3 mm. Some also claim an increased velocity with the overbored barrels, up to 15 m/s (50 feet per second), which is due to the larger swept volume of the overbored barrel. Once only found in expensive custom shotguns, overbored barrels are now becoming common in mass marketed guns. Aftermarket backboring is also commonly done to reduce the weight of the barrel, and move the center of mass backwards for a better balance. Factory overbored barrels generally are made with a larger outside diameter, and will not have this reduction in weight—though the factory barrels will be tougher, since they have a normal barrel wall thickness.

Firing slugs from overbored barrels can result in very inconsistent accuracy, as the slug may be incapable of obturating to fill the oversized bore.

izes in use

Certain sizes are more common than others; 12-gauge is the most common size, with up to 50% of the overall shotgun market in the United States. The 20-gauge shotgun is popular with shooters who are uncomfortable with the weight and recoil of a 12 gauge gun, and is popular for upland game hunting. The next most popular size is the .410 shotgun, which is not a gauge, but a caliber. 10, 16 and 28 gauges, while less common, are still readily available. Shotguns larger than 10-gauge are rarely manufactured nowadays; punt guns and special purpose guns like the European 4-gauge KS-23 do exist, but are rarely encountered. Also seen in limited numbers are smoothbore firearms in calibers smaller than .410, such as .22 Long Rifle, .22 WMR, and 9mm rimfire, designed for short range pest control. [ cite journal |url=http://findarticles.com/p/articles/mi_m0BQY/is_3_46/ai_59281208 |title=Marlin's "Garden Gun" - Model 25MG |journal=Guns Magazine |date=March, 2000 |author=Clair Rees] cite book |title=Cartridges of the World, 10th Ed. |publisher=Krause Publications |author=Frank C. Barnes, ed. Stan Skinner |isbn=0-87349-605-1]

Gauge and shot type

The 10 gauge was headed into obsolescence until steel and other non-toxic shot started to be required for waterfowl hunting, as the larger case could hold the much larger sizes of shot needed to get the low density steel shot to the ranges needed for waterfowl hunting; this same move effectively shut out the 20 and smaller gauges as well. However, the advent of the 3 1/2" (89 mm) 12 gauge shell, with its higher SAAMI pressure rating, meets or exceeds the performance of the 10 gauge loadings. Newer non-toxic shots, such as bismuth and tungsten-nickel-iron alloys, and even tungsten-polymer blends, regain much or all of the performance loss, but at much higher cost than steel or lead shot. [cite web |url=http://www.chuckhawks.com/10_gauge_obsolete.htm |title=Why The 10 Gauge Shotgun is Obsolete |author=Randy Wakeman]

Conversion guide

A table showing the various gauge sizes with weights. The bores marked * are found in punt guns and rare weapons only. The .410 bore is an exception; it is an actual bore size, not a gauge. If the .410 were measured traditionally, it would be 67½ gauge. The European 4-gauge (24 mm, nominal, caliber) is sized slightly different than the traditional 4-bore or 4-gauge, being based on the newer metric 'CIP' tables.



Note: Use of this table for estimating bullet masses for historical large-bore rifles is limited, as this table assumes the use of round ball, rather than conical bullets; for example, a typical 4-bore rifle from circa 1880 used a 2000 grain (4.57 ounce) bullet, or sometimes slightly heavier, rather than using a 4 ounce round lead ball. (Round balls give progressively much worse external ballistic performance than conical bullets at ranges greater than about 75 yards.) In contrast, a 4-bore express rifle often used a 1500 grain (3.43 ounce) bullet wrapped in paper to keep lead buildup to a minimum in the barrel. In either case, assuming a 4 ounce mass for a 4-bore rifle bullet from this table would be inaccurate, although indicative.

See also

* Double rifle
* Elephant gun
* Express rifle
* Smoothbore

External Links

[http://stoppingpower.info/index.php?title=12_gauge 12 gauge shotgun videos]

References


Wikimedia Foundation. 2010.

Игры ⚽ Нужен реферат?

Look at other dictionaries:

  • Gauge — may refer to:In measurements:* American wire gauge, a measurement of diameter of a wire * Gauge (bore diameter), the diameter of a shotgun barrel * Stubs Iron Wire Gauge, which corresponds to the diameter of a hypodermic needle **See also * Sheet …   Wikipedia

  • Bore — may refer to:* Bore (engine), the diameter of a cylinder in a piston engine * Bore (wind instruments), the interior chamber of a wind instrument * Bore (woreda), a district of Ethiopia that includes the town of Bore * Bore, Italy * Gauge (bore… …   Wikipedia

  • bore — bore1 boreable, borable, adj. /bawr, bohr/, v., bored, boring, n. v.t. 1. to pierce (a solid substance) with some rotary cutting instrument. 2. to make (a hole) by drilling with such an instrument. 3. to form, make, or construct (a tunnel, mine,… …   Universalium

  • gauge —    A term used in the identification of a shotgun bore. The number of round lead balls of bore diameter that equal one pound. Thus 12 gauge is the diameter of a round lead ball weighing 1/12 of a pound …   Forensic science glossary

  • Gauge — Gauge, n. [Written also gage.] 1. A measure; a standard of measure; an instrument to determine dimensions, distance, or capacity; a standard. [1913 Webster] This plate must be a gauge to file your worm and groove to equal breadth by. Moxon. [1913 …   The Collaborative International Dictionary of English

  • Gauge cock — Gauge Gauge, n. [Written also gage.] 1. A measure; a standard of measure; an instrument to determine dimensions, distance, or capacity; a standard. [1913 Webster] This plate must be a gauge to file your worm and groove to equal breadth by. Moxon …   The Collaborative International Dictionary of English

  • Gauge concussion — Gauge Gauge, n. [Written also gage.] 1. A measure; a standard of measure; an instrument to determine dimensions, distance, or capacity; a standard. [1913 Webster] This plate must be a gauge to file your worm and groove to equal breadth by. Moxon …   The Collaborative International Dictionary of English

  • Gauge glass — Gauge Gauge, n. [Written also gage.] 1. A measure; a standard of measure; an instrument to determine dimensions, distance, or capacity; a standard. [1913 Webster] This plate must be a gauge to file your worm and groove to equal breadth by. Moxon …   The Collaborative International Dictionary of English

  • Gauge lathe — Gauge Gauge, n. [Written also gage.] 1. A measure; a standard of measure; an instrument to determine dimensions, distance, or capacity; a standard. [1913 Webster] This plate must be a gauge to file your worm and groove to equal breadth by. Moxon …   The Collaborative International Dictionary of English

  • Gauge of a carriage — Gauge Gauge, n. [Written also gage.] 1. A measure; a standard of measure; an instrument to determine dimensions, distance, or capacity; a standard. [1913 Webster] This plate must be a gauge to file your worm and groove to equal breadth by. Moxon …   The Collaborative International Dictionary of English

Share the article and excerpts

Direct link
Do a right-click on the link above
and select “Copy Link”