Transverse isotropy

Transverse isotropy

A transversely isotropic material is symmetric about an axis that is normal to a plane of isotropy. This transverse plane has infinite planes of symmetry and thus, within this plane, the material properties are same in all directions. With this type of material symmetry, the number of independent constants in the elasticity tensor are reduced to 5 from a total of 21 independent constants in case of fully anisotropic solid.

Example of transversely isotropic materials

An example of a transversely isotropic material is the so-called on-axis unidirectional fiber composite lamina where the fibers are circular in cross section. In a unidirectional composite, the plane normal to fiber direction can be considered isotropic. In the figure at left, the fibers would be aligned with the x_3 axis, which is normal to the plane of isotropy.

In terms of effective properties, geological layers of rocks are often interpreted as being transversally isotropic. Calculating the effective elastic properties of such layers in petrology have been coined Backus upscaling, which is described below.

Elasticity tensor

:egin{pmatrix}C_{11}&C_{12}&C_{13}&0&0&0\&C_{11}&C_{13}&0&0&0\&&C_{33}&0&0&0\&&&C_{44}&0&0\&symmetric&&&C_{44}&0\&&&&&(C_{11}-C_{12})/2end{pmatrix}

The elasticity tensor C_{ij} has 5 independent constants, which are related to well known engineering elastic moduli in the following way. These engineering moduli are experimentally determined.

Longitudinal Elastic Modulus, E_L=C_{11}-C_{12}^2/C_{22}

Transverse Elastic Modulus, E_T=C_{22}-C_{12}^2/C_{11}

Inplane Shear Modulus, G_{LT}=C_{66}

Poisson's ratio, Nu_{LT}=C_{11}/C_{22}

Here, L represents the longitudinal direction and T represents the transverse direction; 1 is the fiber direction.

Backus upscaling

A layered model of homogeneous and isotropic material, can be upscaled to a transverse isotropic medium, proposed by Backus [Backus, G. E. (1962), Long-Wave Elastic Anisotropy Produced by Horizontal Layering, J. Geophys. Res., 67(11), 4427–4440] .

Backus presented an equivalent medium theory, a heterogeneous medium can be replaced by a homogeneous one which will predict the wave propagation in the actual medium. [ Ikelle, Luc T. and Amundsen, Lasse (2005),Introduction to petroleum seismology, SEG Investigations in Geophysics No. 12] Backus showed that layering on a scale much finer than the wave length has an impact and that a number of isotropic layers can be replaced by a homeogenous transverely isotropic medium that behaves exactly in the same manner as the actual medium under static load in the infinite wave length limit.

If each layer i are described by 5 transversally isotropic parameters (a_i, b_i, c_i, d_i, e_i), representing the tensor:egin{pmatrix}a_i & a_i - 2e_i & b_i & 0 & 0 & 0 \a_i-2e_i & a_i & b_i & 0 & 0 & 0 \ b_i & b_i & c_i & 0 & 0 & 0 \ 0 & 0 & 0 & d_i & 0 & 0\ 0 & 0 & 0 & 0 & d_i & 0\ 0 & 0 & 0 & 0 & 0 & e_i\end{pmatrix}The elastic moduli for the effective medium will be:egin{pmatrix} A & A-2E & B & 0 & 0 & 0 \ A-2E & A & B & 0 & 0 & 0 \ B & B & C & 0 & 0 & 0 \ 0 & 0 & 0 & D & 0 & 0 \ 0 & 0 & 0 & 0 & D & 0 \ 0 & 0 & 0 & 0 & 0 & Eend{pmatrix}where :egin{align}A &= + ^{-1} ^2 \B &= ^{-1} \C &= ^{-1} \D &= ^{-1} \E &= \end{align}

denotes the volume weighted average over all layers.

This includes isotropic layers, as the layer is isotropic if b_i = a_i - 2e_i, a_i = c_i and d_i = e_i.

Assumptions

* All materials are linearly elastic
* No sources of intrinsic energy dissipation (e.g. friction)
* Valid in the infinite wave length limit, hence good results only if layer thichness is much smaller than wave length

Wave speeds

The direction dependent wave speeds for elastic waves through the material can be found by using the Christoffel equation and are given by [G. Mavko, T. Mukerji, J. Dvorkin. "The Rock Physics Handbook". Cambridge University Press 2003 (paperback). ISBN 0-521-54344-4] : egin{align} V_P( heta) &= sqrt{frac{C_{11} sin^2( heta) + C_{33} cos^2( heta)+C_{44}+sqrt{M( heta){2 ho \ V_{SV}( heta) &= sqrt{frac{C_{11} sin^2( heta) + C_{33} cos^2( heta)+C_{44}-sqrt{M( heta){2 ho \ V_{SH} &= sqrt{frac{C_{66} sin^2( heta) + C_{44}cos^2( heta)}{ ho \ M( heta) &= left [left(C_{11}-C_{44} ight) sin^2( heta) - left(C_{33}-C_{44} ight)cos^2( heta) ight] + left(C_{13} + C_{44} ight) sin^2(2 heta) \ end{align}where egin{align} hetaend{align} is the angle between the TI symmetry axis and the wave propagation direction.

References


Wikimedia Foundation. 2010.

Игры ⚽ Поможем написать реферат

Look at other dictionaries:

  • Isotropy — is uniformity in all orientations; it is derived from the Greek iso (equal) and tropos (direction). Precise definitions depend on the subject area. Exceptions, or inequalities, are frequently indicated by the prefix an, hence anisotropy.… …   Wikipedia

  • Linear elasticity — Continuum mechanics …   Wikipedia

  • Biomechanics — is the application of mechanical principles on living organisms. This includes research and analysis of the mechanics of living organisms and the application of engineering principles to and from biological systems a.k.a bioengineering. This… …   Wikipedia

  • Young's modulus — In solid mechanics, Young s modulus (E) is a measure of the stiffness of an isotropic elastic material. It is also known as the Young modulus, modulus of elasticity, elastic modulus (though Young s modulus is actually one of several elastic… …   Wikipedia

  • Elastic modulus — An elastic modulus, or modulus of elasticity, is the mathematical description of an object or substance s tendency to be deformed elastically (i.e., non permanently) when a force is applied to it. The elastic modulus of an object is defined as… …   Wikipedia

  • Hill yield criteria — Rodney Hill has developed several yield criteria for anisotropic plastic deformations. The earliest version was a straightforward extension of the von Mises yield criterion and had a quadratic form. This model was later generalized by allowing… …   Wikipedia

  • History of special relativity — The History of special relativity consists of many theoretical and empirical results of physicists like Hendrik Lorentz and Henri Poincaré, which culminated in the theory of special relativity proposed by Albert Einstein, and subsequent work of… …   Wikipedia

  • Luminiferous aether — The luminiferous aether: it was hypothesised that the Earth moves through a medium of aether that carries light In the late 19th century, luminiferous aether or ether, meaning light bearing aether, was the term used to describe a medium for the… …   Wikipedia

  • Scale (map) — The scale of a map is defined as the ratio of a distance on the map to the corresponding distance on the ground. If the region of the map is small enough for the curvature of the Earth to be neglected, then the scale may be taken as a constant… …   Wikipedia

  • Tsai-Wu failure criterion — The Tsai Wu failure criterion [Tsai, S. W. and Wu, E. M. (1971). A general theory of strength for anisotropic materials. Journal of Composite Materials. vol. 5, pp. 58 80.] is a phenomenological failure theory which is widely used for anisotropic …   Wikipedia

Share the article and excerpts

Direct link
Do a right-click on the link above
and select “Copy Link”