Flux qubit

Flux qubit

In quantum computing, flux qubits (also known as persistent current qubits) are micrometer sized loops of superconducting metal interrupted by a number of Josephson junctions. The junction parameters are engineered during fabrication so that a persistent current will flow continuously when an external flux is applied. The computational basis states of the qubit are defined by the circulating currents which can flow either clockwise or counter-clockwise. These currents screen the applied flux limiting it to multiples of the flux quantum and give the qubit its name. When the applied flux through the loop area is close to a half integer number of flux quanta the two energy levels corresponding to the two directions of circulating current are brought close together and the loop may be operated as a qubit.

SEM image of a 4-junction flux qubit fabricated at Royal Holloway University of London.

Computational operations are performed by pulsing the qubit with microwave frequency radiation which has an energy comparable to that of the gap between the energy of the two basis states. Properly selected frequencies can put the qubit into a quantum superposition of the two basis states while subsequent pulses can manipulate the probability weighting that the qubit will be measured in either of the two basis states, thus performing a computational operation.

Contents

Fabrication

Like most mesoscopic devices such as solid state qubits, single-electron transistors, quantum dots, etc., flux qubits are fabricated using techniques similar to those used in the micro-electronics industry. The devices are made on silicon wafers using electron beam lithography and metallic thin film evaporation processes. To create the Josephson junction a technique known as shadow evaporation is normally used; this involves evaporating the source metal alternately at two angles through the lithography defined mask in the electron beam resist. This results in two overlapping layers of the superconducting metal, in between which a thin layer of insulator (normally aluminum oxide) is deposited.

Flux qubit parameters

The flux qubit is distinguished from other types of superconducting qubit such as the charge qubit or phase qubit by the coupling energy and charging energy of its junctions. In the charge qubit regime the charging energy of the junctions dominates the coupling energy, while in a flux qubit the situation is reversed and the coupling energy dominates. Typically in a flux qubit the coupling energy is 10-100 times greater than the charging energy. It is this ratio that allows the cooper pairs to flow continuously around the loop, rather than tunnel discretely across the junctions as in a charge qubit.

Readout

Like all quantum bits, Flux qubits require a suitably sensitive probe coupled to it in order to measure its state after a computation has been carried out. Such quantum probes should introduce as little back-action as possible onto the qubit during measurement. Ideally they should be decoupled during computation and then turned "on" for a short time during read-out. Read-out probes for flux qubits work by interacting with one of the qubit's macroscopic variables, such as the circulating current, the flux within the loop or the macroscopic phase of the superconductor. This interaction then changes some variable of the read-out probe which can be measured using conventional low-noise electronics. The read-out probe is typically the technology aspect that separates the research of different University groups working on flux qubits.

Prof. Mooij's group at Delft in the Netherlands[1], along with collaborators, has pioneered flux qubit technology, and were the first to conceive, propose and implement flux qubits as they are known today. The Delft read-out scheme is based on a SQUID loop that is inductively coupled to the qubit, the qubit's state influences the critical current of the SQUID. The critical current can then be read-out using ramped measurement currents through the SQUID. Recently the group has used the plasma frequency of the SQUID as the read-out variable.

Dr. Il'ichev's group at IPHT Jena in Germany[2] are using impedance measurement techniques based on the flux qubit influencing the resonant properties of a high quality tank circuit, which, like the Delft group is also inductively coupled to the qubit. In this scheme the qubit's magnetic susceptibility, which is defined by its state, changes the phase angle between the current and voltage when a small A.C. signal is passed into the tank circuit.

Recently Prof. Petrashov's group at Royal Holloway [3] are using an Andreev interferometer probe to read out flux qubits. This read-out uses the phase influence of a superconductor on the conductance properties of a normal metal. A length of normal metal is connected at either end to either side of the qubit using superconducting leads, the phase across the qubit, which is defined by its state, is translated into the normal metal, the resistance of which is then read-out using low noise resistance measurements.

References

  1. ^ University of Delft - Flux Qubit Website[dead link]
  2. ^ University of Jena - Flux Qubit Website[dead link]
  3. ^ Royal Holloway University of London - Flux Qubit Website

Wikimedia Foundation. 2010.

Игры ⚽ Нужно решить контрольную?

Look at other dictionaries:

  • Charge qubit — Circuit diagram of a Cooper pair box circuit. The island (dotted line) is formed by the superconducting electrode between the gate capacitor and the junction capacitance. In quantum computing, a charge qubit is a superconducting qubit whose basis …   Wikipedia

  • D-Wave Systems — Inc. Type Private Industry Computer hardware Founded 1999 Headquarters Burnaby, British Columbia …   Wikipedia

  • One-Shot Entanglement-Enhanced Classical Communication — In the theory of quantum communication, it is well known that entanglement cannot increase the capacity of a classical communication channel in the sense of Shannon, that is, for an i.i.d. (independent and identically distributed) protocol.… …   Wikipedia

  • Deutsch–Jozsa algorithm — The Deutsch–Jozsa algorithm is a quantum algorithm, proposed by David Deutsch and Richard Jozsa in 1992[1] with improvements by Richard Cleve, Artur Ekert, Chiara Macchiavello, and Michele Mosca in 1998.[2] Although it is of little practical use …   Wikipedia

  • Quantum information — For the journal with this title, see Historical Social Research. In quantum mechanics, quantum information is physical information that is held in the state of a quantum system. The most popular unit of quantum information is the qubit, a two… …   Wikipedia

  • Quantum channel — In quantum information theory, a quantum channel is a communication channel which can transmit quantum information, as well as classical information. An example of quantum information is the state of a qubit. An example of classical information… …   Wikipedia

  • One-way quantum computer — The one way or measurement based quantum computer is a method of quantum computing that first prepares an entangled resource state, usually a cluster state or graph state, then performs single qubit measurements on it. It is one way because the… …   Wikipedia

  • Quantum finite automata — In quantum computing, quantum finite automata or QFA are a quantum analog of probabilistic automata. They are related to quantum computers in a similar fashion as finite automata are related to Turing machines. Several types of automata may be… …   Wikipedia

  • Superconducting quantum computing — This promising implementation of quantum information involves nanofabricated superconducting electrodes coupled through Josephson junctions. As in a superconducting electrode, the phase and the charge are conjugate variables, there exists three… …   Wikipedia

  • Nuclear magnetic resonance quantum computer — Molecule of alanine used in NMR implementation of quantum computing. Qubits are implemented by spin states of the black carbon atoms NMR quantum computing uses the spin states of molecules as qubits. NMR differs from other implementation …   Wikipedia

Share the article and excerpts

Direct link
Do a right-click on the link above
and select “Copy Link”