Transfer switch

Transfer switch

Transfer switches allow switching from a primary power source to a secondary or tertiary power source and are employed in some electrical power distribution systems. Most often transfer switches can be seen where emergency power generators are used to back up power from the utility source. The transfer switch allows safely switching from utility power to emergency generator power while maintaining isolation of each source from the other. The switch may be either a manual switch, an automatic switch, or a combination of manual and automatic. In a home during a power outage, for example, the transfer switch allows isolation of the owner's critical circuits (e.g. cooling, refrigerator, lighting) from the utility service, allowing for operation of the generator without backfeeding to the utility, which can damage utility equipment and hurt (or kill) utility workers.

Automatic transfer switches continually monitor the incoming utility power. Any anomaly such as voltage sags, brownouts, spikes, or surges will cause the internal circuitry to command a generator to start and will then transfer to the generator when additional switch circuitry determines the generator has the proper voltage and frequency. When utility power returns or no anomalies have occurred for a set time, the transfer switch will then transfer back to utility power and command the generator to turn off, after another specified amount of "cool down" time with no load on the generator.

A transfer switch can be set up to provide power to only critical circuits or entire electrical (sub)panels. Some transfer switches allow for load shedding or prioritization of optional circuits, such as heating and cooling equipment.

Break Before Make Transfer Switch

A Break Before Make transfer switch breaks contact with one source of power before it makes contact with another. It prevents backfeeding from an emergency generator back into the utility line, for example. [ [http://www.flatheadelectric.com/custserv/safety/generator/SafetyGenerator.htm] Safely InstallingYour Standby Electric Generator, Flathead Electric Cooperative, Inc.; Jul. 2006; accessed Dec 2006 ] One example is an open transition Automatic Transfer Switch (ATS). During the split second of the power transfer the flow of electricity is interrupted. Another example is a manual three position circuit breaker, with utility power on one side, the generator on the other, and "Off" in the middle, which requires the user to switch through the full disconnect "Off" position before making the next connection.

Closed Transition Transfer Switch (CTTS)

In a typical emergency system, there is an inherent momentary interruption of power to the load when it is transferred from one available source to another (keeping in mind that the transfer may be occurring for reasons other than a total loss of power). In most cases this outage is inconsequential, particularly if it is less than 1/6 of a second.

There are some loads, however, that are affected by even the slightest loss of power. There are also operational conditions where it may be desirable to transfer loads with zero interruption of power when conditions permit. For these applications, closed transition transfer switches can be provided.

When transferring loads in this manner, during a test or when re-transferring to normal after primary power has stabilized, the switch will operate in a make-before-break mode provided both sources are acceptable and synchronized. Typical parameters determining synchronization are: voltage difference less than 5%, frequency difference less than 0.2 Hz, and relative phase angle between the sources of 5 electrical degrees. Since the maximum frequency difference is 0.2 Hz, the engine will generally be required to be controlled by an isochronous governor.

It is generally required that the closed transition, or overlap time, be less than 100 milliseconds. If either source is not present or not acceptable (such as when normal power fails) the switch must operate in a break-before-make mode (standard open transition operation) to ensure no backfeeding occurs.

Closed transition transfer makes code-mandated monthly testing less objectionable because it eliminates the interruption to critical loads, which occur during traditional open transition transfer.

Applications

Typical load switching applications for which closed transition transfer is desirable include data processing and electronic loads, certain motor and transformer loads, load curtailment systems, or anywhere load interruptions of even the shortest duration are objectionable. It should be understood that a CTTS in a system is not a substitute for a UPS (uninterruptible power supply). In addition to providing line conditioning, a UPS has a built-in stored energy that provides power for a prescribed period of time in the event of a power failure. A CTTS by itself simply assures there will be no momentary loss of power when the load is transferred from one live power source to another. [ [http://www.generac.com/Products/Information/TransferSwitches.aspx?commercial] Generac Power Systems Inc., accessed Dec 2006 ]

Utility approval

With closed transition transfer, the on-site engine generator set is momentarily connected in parallel with the utility source. This requires getting approval from the local utility company.

oft-loading Transfer Switch (SLTS)

An SLTS essentially uses CTTS technology but actively changes the amount of load accepted by the generator. [ [http://www.electricity-today.com/et/issue0501/i05_surplus.htm] Pybus, Dennis; Finding Surplus Electric Power in Traditional sources; Electricity Today High Voltage Power & Engineering e-Magazine; accessed Dec 2006 ]

References


Wikimedia Foundation. 2010.

Игры ⚽ Нужно решить контрольную?

Look at other dictionaries:

  • Static Transfer Switch — Der Static Transfer Switch (STS), oder automatischer Transferschalter, ist ein elektronischer Schalter zur Umschaltung auf einen alternativen Stromversorgungspfad in größeren USV Anlagen wie in Rechenzentren. In Rechenzentren wird die… …   Deutsch Wikipedia

  • Charge transfer switch — A charge transfer switch OR CTS charge pump is a charge pump that offers better low voltage performance and a better voltage pumping gain and a higher output voltage [1] than previous charge pumps such as the Dickson charge pump. See also Charge… …   Wikipedia

  • automatic transfer switch — automatinis rezervo jungimo įrenginys statusas T sritis automatika atitikmenys: angl. automatic transfer switch vok. automatische Reserveeinschalteinrichtung, f; automatische Umschalteinrichtung, f rus. устройство автоматического включения… …   Automatikos terminų žodynas

  • Switch — For other uses, see Switch (disambiguation). Electrical switches. Top, left to right: circuit breaker, mercury switch, wafer switch, DIP switch, surface mount switch, reed switch. Bottom, left to right: wall switch (U.S. style), miniature toggle… …   Wikipedia

  • switch — [swich] n. [Early ModE swits, prob. < MDu or LowG, as in MDu swick, a whip, akin to ON sveigr, flexible stalk: for IE base see SWOOP] 1. a thin, flexible twig, rod, stick, etc., esp. one used for whipping 2. the bushy part of the tail in some… …   English World dictionary

  • Switch-technology — is a technology for automata based programming support. It was proposed by Anatoly Shalyto in 1991. It involves software specification, design, implementation, debugging, documentation and maintenance. The term “automata based programming” is… …   Wikipedia

  • Switch — Switch, v. t. [imp. & p. p. {Switched}; p. pr. & vb. n. {Switching}.] 1. To strike with a switch or small flexible rod; to whip. Chapman. [1913 Webster] 2. To swing or whisk; as, to switch a cane. [1913 Webster] 3. To trim, as, a hedge. [Prov.… …   The Collaborative International Dictionary of English

  • switch — index alternate (take turns), barter, change, conversion (change), convert (change use), displace (replace) …   Law dictionary

  • Transfer case — A transfer case is a part of a four wheel drive system found in four wheel drive and all wheel drive vehicles. The transfer case is connected to the transmission and also to the front and rear axles by means of driveshafts. It is also referred to …   Wikipedia

  • switch — n. & v. n. 1 a device for making and breaking the connection in an electric circuit. 2 a a transfer, change over, or deviation. b an exchange. 3 a slender flexible shoot cut from a tree. 4 a light tapering rod. 5 US a device at the junction of… …   Useful english dictionary

Share the article and excerpts

Direct link
Do a right-click on the link above
and select “Copy Link”