Extra-low voltage

Extra-low voltage
IEC voltage range AC DC defining risk
High voltage (supply system) > 1000 Vrms > 1500 V electrical arcing
Low voltage (supply system) 25–1000 Vrms 60–1500 V electrical shock
Extra-low voltage (supply system) < 25 Vrms < 60 V low risk

In electricity supply, the use of extra-low voltage (ELV) is one of several means to protect against electrical shock.[1][2][3][4] The International Electrotechnical Commission and its member organizations define an ELV circuit as one in which the electrical potential of any conductor against earth (ground) is not more than either 25 volts RMS (35 volts peak) for alternating current, or ripple-free 60 volts for direct current under dry conditions. Lower numbers apply in wet conditions, or when large contact areas are exposed to contact with the human body.[further explanation needed]

The IEC defines three types of extra-low-voltage systems (FELV, PELV,and SELV), which are distinguished by their successively more restrictive safety properties.

Contents

Types

Separated or safety extra-low voltage (SELV)

IEC defines a SELV system as "an electrical system in which the voltage cannot exceed ELV under normal conditions, and under single-fault conditions, including earth faults in other circuits".

There exists some confusion regarding the origin of the acronym: "SELV" stands for "separated extra-low voltage" in installation standards (e.g., BS 7671) and for "safety extra-low voltage" in appliance standards (e.g., BS EN 60335).

A SELV circuit must have:

  • protective-separation (i.e., double insulation, reinforced insulation or protective screening) from all circuits other than SELV and PELV (i.e., all circuits that might carry higher voltages)
  • simple separation from other SELV systems, from PELV systems and from earth (ground).

The safety of a SELV circuit is provided by

  • the extra-low voltage
  • the low risk of accidental contact with a higher voltage;
  • the lack of a return path through earth (ground) that electric current could take in case of contact with a human body.

The design of a SELV circuit typically involves an isolating transformer, guaranteed minimum distances between conductors and electrical insulation barriers. The electrical connectors of SELV circuits should be designed such that they do not mate with connectors commonly used for non-SELV circuits.

A typical example for a SELV circuit is a Class III battery charger, fed from a Class II power supply.

Protected extra-low voltage (PELV)

IEC 61140 defines a PELV system as "an electrical system in which the voltage cannot exceed ELV under normal conditions, and under single-fault conditions, except earth faults in other circuits".

A PELV circuit only requires protective-separation from all circuits other than SELV and PELV (i.e., all circuits that might carry higher voltages), but it may have connections to other PELV systems and earth (ground).

In contrast to a SELV circuit, a PELV circuit can have a protective earth (ground) connection. A PELV circuit, just as with SELV, requires a design that guarantees a low risk of accidental contact with a higher voltage. For a transformer, this can mean that the primary and secondary windings must be separated by an extra insulation barrier, or by a conductive shield with a protective earth connection.

A typical example for a PELV circuit is a computer with a Class I power supply.

Functional extra-low voltage (FELV)

The term functional extra-low voltage (FELV) describes any other extra-low-voltage circuit that does not fulfill the requirements for an SELV or PELV circuit. Although the FELV part of a circuit uses an extra-low voltage, it is not adequately protected from accidental contact with higher voltages in other parts of the circuit. Therefore the protection requirements for the higher voltage have to be applied to the entire circuit.

Examples for FELV circuits include those that generate an extra low voltage through a semiconductor device or a potentiometer.

Stand-alone power systems

Cabling for extra-low voltage systems, such as in remote-area power systems (RAPS), is designed to minimise energy losses while maximising safety. Lower voltages require a higher current for the same power. The higher current results in greater resistive losses in the cabling. Cable sizing must therefore consider maximum demand, voltage drop over the cable, and current-carrying capacity. Voltage drop is usually the main factor considered, but current-carrying capacity is an important when considering short, high-current runs such as between a battery bank and inverter.

Arcing is a risk in DC ELV systems, and some fuse types which can cause undesired arcing include semi-enclosed, rewireable and automotive fuse types. Instead high rupturing capacity fuses and appropriately rated circuit breakers are the recommended type for RAPS. Cable termination and connections must be done properly to avoid arcing also, and soldering is not recommended.

Regulations

Australia and New Zealand

ELV is defined in AS/NZS 3000 Wiring Rules with the same voltages as the IEC standard.

In most Australian states (but not all) there are no formal constraints as to who can work on ELV systems. AS 4509.1 Stand-alone Power Systems: Safety requires that work be performed by a "competent person" that is "a person who has acquired through training, qualifications, experience, or a combination of these, knowledge and skill enabling that person to correctly perform the task required".

ELV wiring in domestic premises must be installed at a minimum distance of 50 mm from low voltage wiring or have a separate insulating barrier such a conduit. ELV cable and wire types include PVC insulated building wire, double insulated Thermo-Plastic Sheath (TPS), and fine stranded multi-strand cable (like automotive cable, although this may only be rated to 32 V DC, and not the full ELV range).

State regulations override the Australian Standards, and there are some differences.[5]

References

  1. ^ BS 7671
  2. ^ DIN/VDE 0100-410
  3. ^ IEC 60364-4-41: Low-voltage electrical installations – Part 4-41: Protection for safety – Protection against electric shock.
  4. ^ IEC 61140: Protection against electric shock – Common aspects for installation and equipment.
  5. ^ Stand-alone Power Systems Components. Edition 1 (Dec 2002) Resource Book. Renewable Energy Centre. ISBN 1-876880-31-7

Wikimedia Foundation. 2010.

Игры ⚽ Поможем решить контрольную работу

Look at other dictionaries:

  • extra-low voltage — adjective denoting an electric system with an operating voltage not exceeding 50 volts AC or 120 volts DC. Abbrev.: ELV …  

  • Protective Extra Low Voltage — Als Kleinspannung, umgangssprachlich auch Niedervolt oder Schwachstrom, werden in der Elektrotechnik Wechselspannungen bis 50 Volt Effektivwert und Gleichspannungen bis 120 Volt bezeichnet. Sie ist ein Teilbereich der Niederspannung. Die… …   Deutsch Wikipedia

  • Low voltage — is an electrical engineering term that broadly identifies safety considerations of an electricity supply system based on the voltage used. While different definitions exist for the exact voltage range covered by low voltage , the most commonly… …   Wikipedia

  • low-voltage — /ˈloʊ voʊltɪdʒ/ (say loh vohltij) adjective denoting an electric system with an operating voltage above the extra low voltage range but not exceeding 1000 volts AC or 1500 volts DC …  

  • Voltage converter — A voltage converter changes the voltage of an electrical power source and is usually combined with other components to create a power supply. The term voltage converter is sometimes used as a generic term for a power supply. A voltage converter… …   Wikipedia

  • High voltage — The term high voltage characterizes electrical circuits, in which the voltage used is the cause of particular safety concerns and insulation requirements. High voltage is used in electrical power distribution, in cathode ray tubes, to generate X… …   Wikipedia

  • High-voltage direct current — HVDC or high voltage, direct current electric power transmission systems contrast with the more common alternating current systems as a means for the bulk transmission of electrical power. The modern form of HVDC transmission uses technology… …   Wikipedia

  • Capacitor voltage transformer — A capacitor voltage transformer (CVT), or capacitance coupled voltage transformer (CCVT) is a transformer used in power systems to step down extra high voltage signals and provide a low voltage signal, for measurement or to operate a protective… …   Wikipedia

  • High Voltage (1976 album) — Infobox Album Name = High Voltage Type = Studio Album Artist = AC/DC Released = 14 May, 1976 Recorded = 1974–1975 Genre = Hard rock Blues Rock Length = 44:37 Label = Atlantic Producer = Harry Vanda, George Young Reviews = *Allmusic Rating|4.5|5… …   Wikipedia

  • ELV — extra low voltage …  

Share the article and excerpts

Direct link
Do a right-click on the link above
and select “Copy Link”