Steam turbine locomotive

Steam turbine locomotive

A steam turbine locomotive is a steam locomotive which transmits steam power to the wheels via a steam turbine. Numerous attempts at this type of locomotive were made, mostly without success. In the 1930s this type of locomotive was seen as a way both to revitalize steam power and challenge the diesel locomotives then being introduced.

Advantages of steam turbines
* High efficiency at high speed.
* Far fewer moving parts, hence potentially greater reliability.
* Conventional piston steam locomotives give a varying, sinusoidal torque, making wheelslip much more likely when starting.
* The side rods and valve gear of conventional steam locomotives create horizontal forces that cannot be fully balanced without substantially increasing the vertical forces on the track, known as hammer blow.

Disadvantages of steam turbines
* High efficiency is ordinarily obtained "only" at high speed (though some Swedish and UK locomotives were designed and built to operate with an efficiency equal to or better than that of piston engines under customary operating conditions). Gas turbine locomotives had similar problems, together with a range of other difficulties.

* Peak efficiency can be reached only if the turbine exhausts into a near vacuum, generated by a surface condenser. These devices are heavy and cumbersome.

* Turbines can rotate in only one direction. A reverse turbine must also be fitted for a direct-drive steam turbine locomotive to be able to move backwards.

There are two ways to drive the wheels: either directly via gears, or using generator-driven traction motors.

Direct drive

United States

s being introduced, no more S2s were built. The locomotive was retired in 1949 and scrapped in May, 1952.

United Kingdom

One of the more successful turbines operated in the United Kingdom. The LMS Turbomotive was a 4-6-2 locomotive with no condenser. Despite this, it had greater thermal efficiency than conventional locomotives. The high efficiency mainly resulted from the fact that there were six steam nozzles directed into the turbine which could be turned on and off individually. A certain amount of inspiration appears to have come from Fredrik Ljungström's turbines in Sweden. The main turbine failed after eleven years in heavy service. The Turbomotive was converted to piston drive in 1949 and withdrawn after the deadly Harrow and Wealdstone railway accident in 1952.

One locomotive was built by Beyer-Peacock and used a turbine from Ljungström. Like one of Ljungström's early designs, the driving wheels were under the tender. Performance was disappointing, partly because of poor heating of the boiler.

Another unit was rebuilt by the North British Locomotive Company. In its first incarnation (described below) it had an electrical transmission. Only a few tests were done before it was abandoned due to mechanical failures.

Germany

Multiple attempts at this type were made by German locomotive builders. In 1928 Krupp-Zoelly built a geared steam turbine locomotive. The output of the turbine was fed to a condenser which both conserved water and increased the thermal efficiency of the turbine. Draft for the fire was provided by a steam-driven fan in the smokebox. In 1940 this locomotive was hit by a bomb. It was withdrawn from service and not repaired.

A similar machine was built by Maffei in 1929. Despite having a higher-pressure boiler, it was less efficient than the Krupp-Zoelly locomotive. It was hit by a bomb in 1943 and removed from service.

Henschel converted a normal steam locomotive to use a steam turbine in 1927. Additional driving wheels under the tender were driven by the turbine. The exhaust from the cylinders was fed to the turbine, and the turbine exhaust was fed into a condenser. A smokebox fan provided draft for the fire. Performance was disappointing, and the tender turbine was later removed.

France

Two attempts were made in France. One effort, the Nord Turbine, resembled the LMS Turbomotive in both appearance and mechanical layout. The project was canceled and the locomotive was built as a compound piston steam locomotive instead. The second attempt, SNCF 232Q1, was built in 1939. It was unusual in that its driving wheels were not connected by side rods. Each of its three driving axles had its own turbine. It was heavily damaged by German troops in World War II and was scrapped in 1946.

witzerland

The Swiss firm Zoelly built a turbine locomotive in 1919. It was a 4-6-0 locomotive fitted with a condenser. It was fitted with a cold-air blower feeding into the firebox grate rather than a suction fan in the smokebox. This avoided the complexity of building a fan that could withstand hot, corrosive gases, but introduced a new problem. The firebox was at positive pressure, and hot gases and cinders could be blown out the firebox doors if they were opened while the blower was operating. This potentially dangerous arrangement was eventually replaced with a smokebox fan.

Italy

Giuseppe Belluzzo of Italy designed a number of experimental turbine locomotives. None were ever tested on main lines. His first was a small locomotive with four wheels, each fitted with its own small turbine. Reverse movement was accomplished by feeding steam into the turbines via a backwards-facing inlet. Steam turbines are designed to rotate in only one direction, making this method very inefficient. No one else appears to have attempted it.

Belluzzo contributed to the design of a 2-8-2 locomotive built by Ernesto Breda in 1931. It used four turbines in a multiple expansion arrangement.

In 1933, an FS 2-6-2 locomotive was rebuilt with turbines. It made a test run from Florence to Pistoia and then was never seen again.

weden

Swedish engineer Fredrik Ljungström designed a number of steam turbine locomotives, some of which were highly successful. His first attempt in 1921 was a rather odd-looking machine. Its three driving axles were located under the tender, and the cab and boiler sat on unpowered wheels. As a result, only a small portion of the locomotive's weight contributed to traction.

The second design was a 2-8-0 similar to a successful freight design. Built in 1930 and 1936 by Nydqvist and Holm, these locomotives replaced conventional ones on the Grängesberg-Oxelösund Railway. No condenser was fitted, as its complexity outweighed its thermodynamic advantages. The wheels were driven by a jackshaft. These engines were not retired until the 1950s when the line was electrified. Two examples of this type have been preserved and can be seen in Grängesberg, Sweden.

Argentina

The route from Tucumán to Santa Fe in Argentina goes through mountainous terrain with few opportunities to take on water. In 1925 the Swedish firm NOHAB built a turbine locomotive similar to Ljungström's first design. The condenser worked quite well - only 3 or 4% of the water was lost en route and due only to leakage from the tank. The locomotive had reliability problems and was later replaced by a condenser-equipped piston steam locomotive.

Electric transmission

United States

General Electric built two steam turbine-electric locomotives with a 2-C+C-2 (4-6-6-4) wheel arrangement for the Union Pacific Railroad in 1938. These locomotives were essentially mobile power plants and were correspondingly complex. They were the only condensing steam locomotives ever used in the United States. A Babcock and Wilcox boiler provided steam, and an electric generator was fitted in the front of the locomotive to provide head-end power, a concept that would not catch on until the creation of Amtrak. Boiler control was largely automatic, and the two locomotives could be MUed together, both controlled by one engineer. The fuel was Bunker C oil, the same fuel that was later used in Union Pacific's gas turbine-electric locomotives. Union Pacific accepted the locomotives in 1939, but returned them later that year, citing unsatisfactory results. The GE turbines were used during a motive power shortage on the Great Northern Railway in 1943, and appear to have performed quite well.

In the waning years of steam, the Baldwin Locomotive Works undertook several attempts at alternative technologies to diesel power. In 1944, Baldwin outshopped an S2 class 6-8-6 direct-drive steam turbine locomotive for the Pennsylvania Railroad (see above).

Between 1947–1948, Baldwin built three unique coal-fired steam turbine-electric locomotives, designed for passenger service on the Chesapeake and Ohio Railway (C&O). Their official designation was M1, but because of their expense and poor performance they acquired the nickname "Sacred Cow". The 6,000-horsepower units, which were equipped with Westinghouse electrical systems, had a 2-C1+2-C1-2 wheel arrangement. They were 106 feet (32 m) long, making them the longest locomotives ever built for passenger service. The cab was mounted in the center, with a coal bunker ahead of it and a backwards-mounted conventional boiler behind it (the tender only carried water). These locomotives were intended for a route from Washington, D.C. to Cincinnati, Ohio but could never travel the whole route without some sort of failure. Coal dust and water frequently got into the traction motors. While these problems could have been fixed given enough time, it was obvious that these locomotives would always be expensive to maintain, and all three were scrapped in 1950.

In May, 1954 Baldwin built a 4,500-horsepower steam turbine-electric locomotive for freight service on the Norfolk and Western Railway (N&W), nicknamed the "Jawn Henry" after the legend of John Henry, a track layer who famously raced against a steam drill and won, only to die immediately after. The unit was similar in appearance to the C&O turbines but very different mechanically; it had a C+C-C+C wheel arrangement, and a Babcock and Wilcox water-tube boiler which was fitted with automatic controls. Unfortunately, the boiler controls were sometimes problematic, and (as with the C&O turbines) coal dust and water got into the motors. The "Jawn Henry" was retired from the N&W roster on January 4, 1958.

United Kingdom

The Reid-Ramsey turbine, built by the North British Locomotive Company in 1910, had a 2-B+B-2 (4-4-0+0-4-4) wheel arrangement. Little is known about it, though it appears to have been unsuccessful. It was later rebuilt as a direct-drive turbine locomotive as seen above.

The Armstrong-Whitworth turbine, built in 1922, had a 1-C+C-1 (2-6-6-2) wheel arrangement. It was fitted with a rotary evaporative condenser, in which the steam was condensed by passing it through a rotating set of tubes. The tubes were dampened and cooled by the evaporation of water. The loss of water from evaporation was far less than what it would have been with no condenser at all. The airflow in the condenser had to take a convoluted path, reducing the condenser's efficiency. The locomotive was overweight and a poor performer. It was returned in 1923 and scrapped.

References

* http://www.dself.dsl.pipex.com/MUSEUM/LOCOLOCO/locoloco.htm


Wikimedia Foundation. 2010.

Игры ⚽ Нужна курсовая?

Look at other dictionaries:

  • steam-turbine locomotive — noun : a locomotive propelled by a steam turbine …   Useful english dictionary

  • Steam turbine — A rotor of a modern steam turbine, used in a power plant A steam turbine is a mechanical device that extracts thermal energy from pressurized steam, and converts it into rotary motion. Its modern manifestation was invented by Sir Charles Parsons… …   Wikipedia

  • Turbine locomotive — A turbine locomotive may be one of the following:* A gas turbine locomotive uses a gas turbine as a power source and drives the wheels via a mechanical transmission. * A gas turbine electric locomotive also uses a gas turbine, but the turbine… …   Wikipedia

  • Gas turbine locomotive — A Gas turbine locomotive is a locomotive powered by a gas turbine. The majority of gas turbine locomotives have had electric transmission but mechanical transmission has also been used, particularly in the early days. The advantage of using gas… …   Wikipedia

  • turbine locomotive — noun : a locomotive powered by a steam or gas turbine engine that transmits motion directly to the driving wheels through gearing or that drives generators for producing electricity for the electric motors that move the driving wheels …   Useful english dictionary

  • Steam locomotive — A steam locomotive is a locomotive powered by steam. The term usually refers to its use on railways, but can also refer to a road locomotive such as a traction engine or steamroller.Steam locomotives dominated rail traction from the mid 19th… …   Wikipedia

  • Turbine (disambiguation) — A turbine is a rotary engine that extracts energy from a fluid flow.Other pages about turbinesTypes of turbines*Gas turbine:*Jet engine:*Turbojet:*Turbofan:*Turbocharger:*Turboshaft*Steam turbine:*Compound turbine*Wind turbine:*Vertical axis wind …   Wikipedia

  • steam engine — steam engine, adj. an engine worked by steam, typically one in which a sliding piston in a cylinder is moved by the expansive action of the steam generated in a boiler. [1745 55] * * * Machine that uses steam power to perform mechanical work… …   Universalium

  • locomotive — locomotively, adv. locomotiveness, locomotivity, n. /loh keuh moh tiv/, n. 1. a self propelled, vehicular engine, powered by steam, a diesel, or electricity, for pulling or, sometimes, pushing a train or individual railroad cars. 2. an organized… …   Universalium

  • Steam engine — A steam engine is a heat engine that performs mechanical work using steam as its working fluid. [ [http://www.britannica.com/EBchecked/topic/564472/steam engine steam engine Britannica Online Encyclopedia ] ] Steam engines have a long history,… …   Wikipedia

Share the article and excerpts

Direct link
Do a right-click on the link above
and select “Copy Link”